here ya go
compliments of basskiller
Making your own gear from powders
Information Bulletin - The use of Powder
steroids
First of all, on the virtues of powdered
steroids : You may be a little weary
about ordering raw materials for
steroids instead of ready-made tabs, amps or
vials, but we will put your mind at ease in a minute here. Contemplate the
benefits of powders :
1.The cost is only 40-60% of the normal cost
2.They take only a short time to prepare
3.They are easier and cheaper to ship than amps or vials
4.Less chance of your order getting seized by customs
5.Unlike vials and amps, they come with a refund/reship policy
PREPARING THE POWDERS FOR ORAL USE
This is really only applicable to the 17AA
steroids OXandrolone, Stanabol and
Anabol. These are the only ones that are orally available. In principle the
boldenone undecylenate oil can be taken orally, but daily doses of 200 mg are
required, which is basically a waste of money, if a 400 mg per week injection
can achieve the same.
Pick up some sesame oil at the health store and find a container for the liquid.
Determine the concentration. For Stanabol I recommend 25 mg/ml, for Anabol and
Oxandrolone I suggest 20 mg/ml. Say you have 1 gram of Anabol. That's 1000 mg.
At 20 mg per ml that equates to
50 ml of oil. So for every gram of powder you have you will make 50 ml of
solution. Fill the container up with water, 50 ml per gram. If you have 5 grams,
then that's 250 ml. Mark that spot on the container. Dump out the water and let
the container dry. Dump the powder in the container and then add oil until you
reach the mark you made on the container. You know have your solution at 20
mg/ml.
I suggest taking 2 ml per day (40 mg) in the morning. Use a
syringe to measure
out 2 ml and squirt it in your mouth, wash it down with the beverage of your
choice. Remember to never use a 17AA
steroid longer than 6, at the very longest
8 weeks on end, because these substances are toxic to the liver.
Remember that you need 50 ml per gram of powder for ox and anabol and 40 ml for
stanabol. This does not mean 50 and 40 ml of oil, it means 50 or 40 ml of oil,
minus the space the powder takes up.
PREPARING THE POWDERS FOR INJECTABLE USE
These things can be quite confusing, so since testosterone enanthate and
boldenone undecylenate come pre-packaged per 5 grams, I will detail the
conversion for both for 5 grams, so you can copy the method exactly.
Testosterone enanthate :
You will need
benzyl alcohol,
syringes, a container that will hold 20 ml and oil
(arachis or sesame oil). Because we will inject this, the oil needs to be
sterile. To sterilize it heat the oil to 212 degrees F (100 degrees C). In the
mean time use a
syringe to fill your container with EXACTLY 20 ml of pure water.
Mark the container at the water level. use the
syringe to take out 0.6 ml and
make another mark. Your container is now marked at 19.4 ml and 20 ml. Dump out
the water and let the container dry. let the oil cool off.
Dump the powder (5 g) in the container, add oil until it reaches the 19.4 ml
mark. Then add
benzyl alcohol until it reaches the 20 ml mark.
read the bottom update
Seal your
container and shake it well. You are now ready to use the product. It is a
testosterone enanthate solution at 250 mg/ml. I suggest a weekly injection of 2
ml (500 mg) for a period of 10 weeks. At this rate the product will last you
exactly 10 weeks.
Boldenone Undecylenate (Equipoise)
You will need
benzyl alcohol,
syringes, a container that will hold 25 ml and oil
(arachis or sesame oil). Because we will inject this, the oil needs to be
sterile. To sterilize it heat the oil to 212 degrees F (100 degrees C). In the
mean time use a
syringe to fill your container with EXACTLY 25 ml of pure water.
Mark the container at the water level. use the
syringe to take out 0.8 ml and
make another mark. Your container is now marked at 24.2 ml and 25 ml. Dump out
the water and let the container dry. let the oil cool off.
Dump the boldenone oil (5 g) in the container, add oil until it reaches the 24.2
ml mark. Then add
benzyl alcohol until it reaches the 25 ml mark. Seal your
container and shake it well. You are now ready to use the product. It is a
boldenone undecylenate solution at 200 mg/ml. I suggest a weekly injection of 2
ml (400 mg) for a period of 10-12 weeks. At this rate the product will last you
12.5 weeks.
17AA
steroids : Oxandrolone, Anabol and Stanabol
You will need purified water,
benzyl alcohol,
syringes and a container that
holds 40 ml for every gram of powder you have. The water needs to be pure and
sterile because it will need to be injected. First fill up your container to the
desired level of water (40 ml per gram of powder) and make a mark. Then use the
syringe to remove 1 ml per gram of powder you have and make another mark. Let
the container dry. Dump the powder in the container and fill up with sterile
water up to the lowest mark. Then add
benzyl alcohol to the highest mark. Seal
the container and shake well. The powder should sink to the bottom if left
unshaken. Make sure you shake prior to each use. I suggest using 2 ml DAILY
injections for a period of 8 weeks.
Some people believe that water-based
steroids can provide local growth, ie
muscle growth in the muscle it is injected into. If you are such a person, these
products would do the trick. to learn how to spot inject, visit
spotinjections.com.
Just so that you all know, I did not write this, Just posted it...
UPDATE.. I think that it is better to add your powder to the BA first and let it disolve somewhat first before adding the oil! then heat the mixture up as to dissolve it further. It seem to work out better this way...
Plus You may find the littlest bit of gunk afterwards.. (because at best the powders are 99% pure....
Then move on to the filtering!
Linear Mode
