WHICH TEST IS THE BEST?

[MarkoPolo]

WHICH KIND OF TEST IS THE BEST FOR A BULKING CYCLE?

[big_b_69]

/;

[Oldman]

TEST is TEST. only the esters make a difference in how long it takes to work. I like cyp. Its an easier shoot than prop or sus. Some people like prop better for cutting because it is in and out of you much quicker and not able to cause as much bloat. I say use arimidex.

[cal]

euro and cheap is the main criteria...

[basskiller]

Mg for mg Test suspension is best, can hurt like hell but here is why it's the best.
It's the only one without an ester. The ester chains that are attached to all the other tests, weigh something and take up room. So there is less of the parent steroid. the longer the chain, the less of the parent steroid.

So the test that has no ester would in fact be the best.


Now for which one I like the best, I'd say test enanthate. Not as many shots per week. Especially when your also doing fina.
As it is, I already feel like a pincushion.

[SouthBeachDream]

the injectable kind!!!/- Really though, I love Enanthate./t\

[Abombs]

I like taking huge amounts of cheap Mexican test. you can't beat 10 bottles of tornel for $300

[buffarat]

that is awsome.........abombs................hook it up. ANyway, test is test is test in my book. Although i have gotten faster results on suspension.

[preist943]

eth is king in my game

[BlackSuperman]

I love ethanate But I dont agree with A-Bomb I am not stickin myself with mexican piss I pay the same price for testex EURO actually less!! So no dirty oil for me!

Bigggman

[xcelbeyond]

As Basskiller said, here's info regarding test esters from my archives:

High Mg per ML Roids, What you need to know – by Iron Addict
--------------------------------------------------------------------------------------------
Not a week goes by that I don't get personal email questions from people about how to make high mg per ml gear. There are also lots of these posts on the boards so I'm taking a moment to clear a couple of things up.

1. Most hormones have a pretty low solubility in oil.
2. The primary ways to increase solubility are to
A) add solvent (BA or EA).
B) Add an ester to the hormone. The longer the ester the more hormone will fit in the oil at a certain mg per ml ratio. Conversely, the weight of the ester is also factored in the total mg per ml ratio, so while you can fit more hormone in, you are getting less actual hormone than the mg amount implies. Here are some examples:

Ester actual mg/100mg dose
test no ester 100
tren acetate 87
test prop 83
test enanth 72
test cyp 70
test undecan 63
nand phenyl 67
nand deca 64

This means that if your test cyp says 200 mgs per ml you get an actual 140 mgs of test. The rest of the weight is the weight of the ester. If that sounds like a bad deal you need to understand that test no ester is VERY insoluble in oil without going to very high mg per ml solvent concentrations.

This brings up the next point; PAIN!

Why do some shots hurt? There are two primary reasons. One, the solvent ratio is too high. Anything over about 10% starts to hurt. BA and EA are VERY inflammatory to the tissues. That’s why you want ONLY enough to help your oil hold more gear but not so much that it causes inflammation.

The second reason is that the gear crystallizes in the depot. This is precisely why water-based suspensions feel like hammer blows. The water is absorbed FAST, leaving the gear to crystallize in the tissues = PAIN. Even gear in oil can do this, here is how it works. If you use a low ester weight attached to your gear and make the mg per ml ratio SIGNIFICANTLY higher than the oil will hold on it's own, what happens is the body absorbs the solvent faster than the oil/gear and the gear falls out of the solution and crystallizes in the depot and WHAM, it hurts like hell. An optimum solution has just enough solvent to get more gear into solution than you could otherwise, but not so much that what I just stated happens. When the ratios are correct the gear holds in the solution UNTIL the whole depot is absorbed and very little or no pain is felt. Just to end this misconception once and for all IT IS NOT THE VOLUME OF THE OIL THAT CUASES THE PAIN, IT IS ONE OF THE CONDITIONS STATED ABOVE. You can shoot 5 cc's of sterile oil and never know you took a shot. It IS NOT HOW MUCH OIL YOU SHOOT! So why does everyone search for super high mg per ml ratio gear like it's the damn holy grail???

What is too high? Well the length of the ester is really what determines that but most of us here know the gear that hurts and know we know why. All tests over 250 mgs per ml hurt, and actually most of the 250 mg tests hurt too. SOOOO many people want there tren at 150-200 mgs per ml. Tren acetate should be at about what????? 75 mgs per ml. That is why all the kits are designed this way. Do you really think it's cheaper for the kit producers to add MORE oil to their kits instead of less? One other quick note. Oil is used because it SLOWS absorption. THIS IS PRECISELY WHAT YOU WANT IN A STEROI* SHOT! Less oil does not promote the steady state hormone levels achieved with more oil.

xcelbeyond /t\

[FRKNHUGE]

get a few btl of each and load 1/2 eod, lol
see which is best, lol
this post was a joke guys, lol


frk

[swoo]

IP PROP/suspension some wicked shit

[basskiller]

Thats a nice post, X./t\

[slide]

Bump for the info xcel gives.../t\

---slide---